Honestly I’m sure this is the best solution. I get that a d4 is the obvious choice for something that should have a 1/4 chance of happening but a d8 with 4 numbers twice would be the most appropriate.
The only downside I can see is that a d8 and a d8/4 would be easy to mix up at first glance.
Am I missing something here? Can this even generate 5 or 7?
D20/5 gives [1…4] and D20/10 [1…2], of course assuming whole numbers. Where to get the factors for 5? 5 can be factored only as 5x1 or 1x5 and the 5 cannot be found either in d20/5 or d20/10. Same is true for 7.
And I don’t see it happening either if we allow rational numbers. To get 5 we would get the following expressions
5= d120/5 x d220/10 = d120 x d220/50
or
250= d120 x d220
And two d20 multiplied together cannot give us 250.
You are right, in my mind the d20/2 was some sort of iterator over the d20/5, the correct math would be d20/5+(20/5*(d20/10-1)). To get 5 this expresion would be with a 1-5 in the first one and a 11-20 on the second, the first would be 1 (rounded up) , and the second one 4*(2-1), so 5. The idea is that you use the second one to decide how many batches of the full first batch you add to the first one. As if you were rolling a d100 with two d10 but in base 20/5 instead of base 10. It’s not actually base 20/5 but that’s the idea, one of the dice is the “tens” dice and the other is the “hundreds” dice.
But then do really need the d8? If we toss that in the bin we can go to the universal d60. This one dice will allow us to get
d2 (even/odd)
d3 (d60/20)
d4 (d60/15)
d5 (d60/12)
d6 (d60/10)
d10 (d60/6)
and d12, d15, d20, d30
They’re only off by about 1% and the bias depends on which side was up, it’s not that bad. I wouldn’t expect most inexpensive dice to be substantially fairer than that.
I’d actually like to see a d8/d4 hybrid. Basically take a caltrop d4, snip a bit off the ends to make a truncated tetrahedron. You’ll then have 4 large hexagonal faces and 4 small triangular ones. Put the numbers on the triangles. If it lands upside down, then it is just house rules whether to use the bottom face or to reroll. Or just number the large faces too.
It’s a similar concept to the round safety d4s; just less… round.
d8s with duplicate sides gang
Honestly I’m sure this is the best solution. I get that a d4 is the obvious choice for something that should have a 1/4 chance of happening but a d8 with 4 numbers twice would be the most appropriate.
The only downside I can see is that a d8 and a d8/4 would be easy to mix up at first glance.
You don’t even need a special die for this. Just roll a d8 and subtract 4 if it’s 5-8. Just like using a d6 as a d3.
I always divide by two and round up for d3
Honestly you only need a d20 and a d6. D4? Divide by 5. D8? D20/5 x d20/10. D12? D6xd10/2
MATH BABY
Am I missing something here? Can this even generate 5 or 7?
D20/5 gives [1…4] and D20/10 [1…2], of course assuming whole numbers. Where to get the factors for 5? 5 can be factored only as 5x1 or 1x5 and the 5 cannot be found either in d20/5 or d20/10. Same is true for 7.
And I don’t see it happening either if we allow rational numbers. To get 5 we would get the following expressions
5= d120/5 x d220/10 = d120 x d220/50
or 250= d120 x d220
And two d20 multiplied together cannot give us 250.
Math baby?
You could do something like ((d6-1)*20+d20)/15.
But that’s an awful lot of work just to avoid having a d8.
You are right, in my mind the d20/2 was some sort of iterator over the d20/5, the correct math would be d20/5+(20/5*(d20/10-1)). To get 5 this expresion would be with a 1-5 in the first one and a 11-20 on the second, the first would be 1 (rounded up) , and the second one 4*(2-1), so 5. The idea is that you use the second one to decide how many batches of the full first batch you add to the first one. As if you were rolling a d100 with two d10 but in base 20/5 instead of base 10. It’s not actually base 20/5 but that’s the idea, one of the dice is the “tens” dice and the other is the “hundreds” dice.
… math baby
I hate math babies. Least favorite type of baby.
Math baby.
But then do really need the d8? If we toss that in the bin we can go to the universal d60. This one dice will allow us to get
d2 (even/odd)
d3 (d60/20)
d4 (d60/15)
d5 (d60/12)
d6 (d60/10)
d10 (d60/6)
and d12, d15, d20, d30
Base 60 is cool yo!
that dice would either be really big, or it would just be a ball that would take too long to stop rolling lol… I want it now.
I have a “D3” that’s just a D6 with two of each.
Flipping a coin two times and reading the result as binary gang. (Don’t actually do this, coins aren’t as fair)
They’re only off by about 1% and the bias depends on which side was up, it’s not that bad. I wouldn’t expect most inexpensive dice to be substantially fairer than that.
Would spinning the coin get rid of that bias?
I have not read any stats on coin spinning, so I don’t know!
I suppose it’s basically flipping turned 90 degrees, so it might still be affected but which face is forward when being spun.
D12 with numbers in triplicate appreciators over here
D100 with 25 of each option lover right here
I’d actually like to see a d8/d4 hybrid. Basically take a caltrop d4, snip a bit off the ends to make a truncated tetrahedron. You’ll then have 4 large hexagonal faces and 4 small triangular ones. Put the numbers on the triangles. If it lands upside down, then it is just house rules whether to use the bottom face or to reroll. Or just number the large faces too.
It’s a similar concept to the round safety d4s; just less… round.
Wilder option which is definitely hard to mass produce:
A truncated tetrahedron like this but with wireframe corners, so it rolls like a D4 but there is a clear upward face.
Like this?
https://www.kickstarter.com/projects/263612668/rollable-4-sided-dice
They’re out there somewhere…