https://hackaday.com/2022/09/05/food-safe-3d-printing-a-study/

So I sliced and printed a different model, and then rotated 1 by 180°, it is somewhat weird as the lowest part on the right model seems ok but as the wall built up on the inside it was getting the artifacts. The model on the left was getting the artifacts on the outer piece but not the inner.

In rotating the models after, the artifacts are on the opposite side.

I noticed it was starting at the seam, I have the scarf joint on contour, and noticed that “scarf around entire wall” was checked so trying reprinting to see if that is the issue.

Good point, I have mainly been printing these items for the hydroponic tower. I do have other versions that I can check. I think after this set prints I will add some basic shapes in different orientations to see if there is issues still.

That being said I did print some other items that were stacked and each one is much thinner but there are no artifacts on the outer walls.

Thanks for your reply, to your point yes they still fit, been having this issues for a bit now as I’m up to about 40 of these netcups and the associated other pieces for the grow towers.

I think the belts are good, but will double check.

Depending on how close you are to you friends you can look at Grohman

https://grohmannknives.com/index.php/products/kitchen

The are based on Nova Scotia.

Easy there pussies can be useful, unlike that shitheel.

Funny and sad that the Canadian taxpayers are footing the bill for some friend of a friend to have a luxury condo in NYC. These so called leaders are just milking everyone. What a disgrace.

I can’t speak to multi colour perse, however the creality K2 went on sale today for certain countries and they have a 50% off sale for a limited number of units, they sold out today’s stock but will have it again tomorrow then they will drop to 40% then 30%. Might be good if your willing to be a beta tester essentially.

The Prusa units seems to waste less filament.

I’m building a low pro Corne, Kailh browns with ChocFox keycaps, it’ll be my travel keyboard.

Currently I’m doing the bed level with everything at room temperature.

I’ll give it a try heated to see if that is causing the warping.

Cheers.

I have it clear the mesh, take a new mesh as default, and load default mesh in my start profile.

I though it might be the same, but it does make micro movements along the board to adjust for the mesh reading.

Double checked the operation of the BL Touch, it’s working and no issue (mechanically at least).

I did a complete relevel of the bed and still had an issue in the middle of the bed. Commented out the bed mesh in my config and had a better result in the middle of the bed.

Running with no BK Touch for now.

Thanks.

I’ll give that a go. Thanks for the idea.

I’ll try running sans BL Touch, it’s just weird that it was working before the board change without issue. I’ve cranked down on the silicon spacers to make sure it’s difficult for them to loosen up over time, will see how that goes.

Thanks for your comment.

How many prints do you think you’re putting through before you’re cleaning it.

I run mine through a porous rock filter (I’ll try to find the video link) every couple of months.

Typically I pre wash with Mean Green, then into the isopropyl which helps extend the life of the isopropyl.

Check out https://www.aneros.com/ you also might be able to find similar styles for less money.

They have what you are describing as well as lots of resources to help you on your journey.

Vibration is not required, for some it overstimulates, but it can be fantastic. One thing you mentioned wear"head space" and this will be important in getting where you want to go, but it helps to learn how to relax your mind and be in the moment.

Also checkout r/prostateplay on Reddit, there is tons of useful information and a great community to learn from, I haven’t found a replacement on Lemmy yet.

This is a bit older bit still has good information.

https://m.youtube.com/results?sp=mAEA&search_query=lmds+greenfrog

He walks through setting up Raspberry Pi’s and the Arrs. Can use his setup or just the information.